Cisco,CCNA,CCNP,Certification, computer Cisco CCNA / CCNP Certification Exam Tutorial: EIGRP And Sp
Gone are those times when the companies and the organisations didn't need a hi-tech system to handle them. Owing to the considerable increase in the business sector and thus, an enormous increase in the complexity of the organisational struc ----------------------------------------------------------Permission is granted for the below article to forward,reprint, distribute, use for ezine, newsletter, website,offer as free bonus or part of a product for sale as longas no changes a
EIGRP is a major topic for your CCNA and CCNP studies, and one basic skill youll need to pass your Cisco certification exams is to identify situations where you need to enable or disable split horizon. EIGRP commands tend to be a little different than those used with other protocols, so lets take a look at how EIGRP and split horizon interoperate.R1 is our hub router, with R2 and R3 as the spokes. There are no subinterfaces, and each router is advertising a single loopback network using its router number for each octet. R1 will see both R2 and R3s loopback network, but the spokes will not have a route to the other spokes loopback. show ip route eigrp verifies this.R1#show ip route eigrp 2.0.0.0/32 is subnetted, 1 subnetsD 2.2.2.2 [90/2297856] via 172.12.123.2, 00:03:29, Serial0 3.0.0.0/32 is subnetted, 1 subnetsD 3.3.3.3 [90/2297856] via 172.12.123.3, 00:03:29, Serial0R2#show ip route eigrp 1.0.0.0/32 is subnetted, 1 subnetsD 1.1.1.1 [90/2297856] via 172.12.123.1, 00:05:20, Serial0R3#show ip route eigrp 1.0.0.0/32 is subnetted, 1 subnetsD 1.1.1.1 [90/2297856] via 172.12.123.1, 00:07:54, Serial0EIGRP runs split horizon by default, making it impossible for R1 to forward an advertisement to R2 regarding R3s loopback. Likewise, R1 cannot advertise R2s loopback address to R3. We could configure two subinterfaces on R1 to resolve this issue, but here were going to disable split horizon instead. R1(config)#int serial0R1(config-if)#no ip split-horizon ? eigrp Enhanced Interior Gateway Routing Protocol (EIGRP) R1(config-if)#no ip split-horizon eigrp ? Autonomous system numberR1(config-if)#no ip split-horizon eigrp 10004:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is down: split horizon changed04:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is down: split horizon changed04:10:25: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is up: new adjacency04:10:37: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is up: new adjacencyNote that disabling split horizon resulted in the EIGRP adjacencies being torn down. They came back up 20 35 seconds after being torn down according to the timestamps, but thats a good detail to keep in mind! The routing tables of each spoke should now show the loopback network configured on the remote spoke.R2#show ip route eigrp 1.0.0.0/32 is subnetted, 1 subnetsD 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0 3.0.0.0/32 is subnetted, 1 subnetsD 3.3.3.3 [90/2809856] via 172.12.123.1, 00:00:02, Serial0R3#show ip route eigrp 1.0.0.0/32 is subnetted, 1 subnetsD 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0 2.0.0.0/32 is subnetted, 1 subnetsD 2.2.2.2 [90/2809856] via 172.12.123.1, 00:00:02, Serial0Be careful when disabling split horizon. In this scenario, R1 can and will advertise routes out Serial0 that were learned about on that interface in the first place, and thats not always desirable. Split horizon is enabled by default for a reason, so be careful when disabling it!
Cisco,CCNA,CCNP,Certification,