What,Should,You,Know,Before,Us communication What Should You Know Before Using an OTDR?
But when we talk about the handsets, undoubtedly, Nokia is the King of mobile phone market and LG stood at the third position. In this article we are concentrating on Nokia E5 from the house of Nokia and LG GM360 Viewty Snap by LG Mobile Com The Nokia Mobile Company is the undisputed leader in mobile world, they have latest technology and capability to deliver world class handsets at no extra costs. The N series, E series and C series phones have already rocked the world with th
OTDR, the optical time domain reflectometer, is the most important investigation tool for optical fibers. It’s applied in the measurement of fiber loss, connector loss and for the determination of the exact place and the value of cable discontinuities. It’s the only device which can verify inline splices on concatenated fiber optic cables and locating faults.To know how to use OTDR for the fiber investigations, first you should know the structure and working principle of OTDR equipment. When a short light pulse transmits into the fiber under test, the time of the incidence and the amplitude of the reflected pulses are measured. The commonly used pulse width ranges from nanosecs to microsecs, the power of the pulse can exceed 10 mW. The repetition frequency depends on the fiber length, typically is between 1 and 20 kHz, naturally it is smaller for longer fibers. The division by 2 at the inputs of oscilloscope is needed since both the vertical (loss) and the horizontal (length) scales correspond to the one-way length.Besides, to use an OTDR successfully, you should also know how to operate the instrument. The following is about the experiences collected from some experienced people who use OTDRs during installation and for maintaining telecommunication networks.Keep Connectors CleanBefore use OTDR, first, you should watch out if the connectors are clean. If it’s dirty, then clean it. Otherwise, it will make measurements unreliable, noisy or even impossible. What’s worse, it may damage the OTDR.Check the Connector or the Patch CordCheck whether the patch cord, the module, and the fiber under test are single-mode or multimode. To test the patch cord, activate the laser in the CW (Coarse Wavelength) mode and measure the power at the end of the patch cord with a power meter. This should be between 0 and - 4 dBm for most single-mode modules and wavelengths.Set the RangeThe range is the distance over the cable which the OTDR will measure. The range should be longer than the cable you are testing. For example, if your link is 56.3 km long, choose 60 km. For distances greater than approximately 15 km, make your first measurement in longhaul mode, otherwise use shorthaul.Determine the WavelengthUsually single-mode is set for 1310 nm or 1550 nm, and multimode is set for 850 nm or 1300 nm.Averages of Noisy TracesIf the trace is very noisy, increase the number of averages. Usually 16-64 averages are adequate. To improve the signal to noise ration of the trace, the OTDR can average multiple measurements, but averaging takes time. So try to average over a longer time.Realtime ModeIn this mode, you can modify parameters only if you stop a measurement explicitly. So it avoids you to erase a trace averaged over a long time by accident. You use realtime mode to check your connection, the quality of splices, and whether a fiber is connected. Start in automatic mode, then switch to realtime mode and select the most suitable parameters.Adjust the Refractive IndexIf you know the exact physical length of the fiber under test, you can measure the refractive index. Start with the refractive index 1.5000. Place a marker at the end of the fiber. Then select the refractive index function and adjust it until the displayed marker position is equal to the known fiber length. Then, the effective refractive index will be displayed.Macrobending LossSingle-mode fibers (1550 nm) are very sensitive to macrobending such as a tight bend or local pressure on the cable. It doesn’t always happen at this wavelength of 1310 nm. So characterize your link at both wavelengths.OTDRs are invaluable test instruments. Maybe a small mistake will cause serious damage to this equipment. So before use it, you should better know it as detailed as possible to avoid any loss because of innocence and make full use of it in optical fiber events. Article Tags: Fiber Under Test, Fiber Under, Under Test, Patch Cord, Realtime Mode, Refractive Index
What,Should,You,Know,Before,Us